iVA Intelligent Vibration Analyzer
$3,080.00
The iVA uses Quad Vibration Technology™ (QVT). This technology locates and identifies the vibration then rates the vibration severity with advanced color coding. The iVA locates multiple vehicle vibrations simultaneously. The iVA displays a vehicle topology map that highlights the severity of vibrations with yellow, orange, and red. No need to analyze graphs or charts, but these are easily accessible at any time.
The Next Level in Noise & Vibration Analysis!


















Finally a quick and easy way to find difficult vibration issues!
The iVA simplifies setup!
Eliminates the need for separate hardware such as an oscilloscope and J2534 device. All you need to start testing is your Windows PC. To start; enter the Tire Size, Ring and Pinion Ratio and Vehicle Drive Type (Front Wheel Drive, Rear Wheel Drive, All wheel drive, and Four Wheel Drive). If the Ring and Pinion is unknown the iVA will automatically calculate the Ring and Pinion Gear Ratio. Simply attach the magnetic sensors to the suspension components. Setup takes less than 5 minutes in most cases!
Comes with everything you need for use on your Windows based PC

Intelligent Vibration Analyzer Module™
The Intelligent Vibration Analyzer Module™ (iVA Module) houses an advanced electronic system that contains a Data Acquisition Device (DAQ) for sampling the signals from the Smart Vibration Sensors and iVA Microphones. The iVA Module also contains a Vehicle Communications Interface (VCI) that communicates with vehicle Engine Control Modules from 1996 to present. Communication Bus Types Supported; J1850 VPW, J1850 MPW, J1850 PWM with IFR, ISO 9141-2, KPW2000, KPW2000 Slow init, and CAN

Smart Vibration Sensor™
The Smart Vibration Sensor™ (SVS) uses multiple 3-axis accelerometers (X, Y and Z) to locate vibrating components. These are smart sensors in that they allow all three channels from the accelerometer to be monitored at all times. This is accomplished by summing the X, Y and Z channels being monitored within the vibration sensor itself. That way the total amplitude produced from the X, Y or Z channels is analyzed. This will enable the DAQ to read the total amplitude from all three accelerometer axis produced from the sensor providing vibration in all directions. When four vibration sensors are used the iVA DAQ can monitor 12 accelerometer (X, Y and Z) axis continuously.

iVA Microphone Clamp
The iVA Microphone Clamp is an amplified 20-20KHz electric microphone that picks up sounds waves from the metal components. The iVA Microphone Modes then process these sound waves using a Fast Fourier Frequency (FFT), which is the default reading, a Frequency Plot (FP), or can be played with a WAV audio file that is either live or recorded. The iVA Microphone Clamp quickly attaches with a spring clamp.

iVA Microphone
The iVA Microphone is an amplified 20-20KHz electric microphone that picks up sounds waves from the surrounding air. The iVA Microphone Modes then process these sound waves using a Fast Fourier Frequency (FFT), which is the default reading, a Frequency Plot (FP), or can be played with a WAV audio file that is either live or recorded. The iVA Microphone quickly attaches with a built-in neodymium rare earth magnet.

iVA Stereo Jack Cable
The iVA Stereo Jack Cable is a 20 ft cable that comes in 4 colors; Yellow, Red, Green, and Blue. These cables quickly attach with neodymium rare earth magnet cable holders that are attached to the cable.

iVA Data Link Connector
The iVA Data Link Connector Cable allows the iVA Module to connect to the DLC on the vehicle. This allows the iVA Module to communicate with the Engine Control Module on the vehicle.

iVA C-Clamps
The iVA C-Clamps attach the Smart Vibration Sensors and iVA Microphones to components that are nonmagnetic. The C-Clamps are attached using a clamping force to components made from metals such as aluminum. The Smart Vibration Sensor and iVA Microphones then attach to the flat surface of the C-Clamp.

iVA USB Cable
The iVA USB Cable connects the iVA Module to your Windows based Personal Computer (PC). This cable allows the iVA Module to transmit data to the PC. The PC then process this data with the advanced iVA software.

iVA Pressure Sensitive Tape
The iVA Pressure Sensitive Tape is used to attach the iVA Stereo Jack Cables to the painted surfaces of the vehicle. This tape is a residue-free tape that will not damage paint or leave any film on painted surfaces.

iVA Tape Measure
The iVA Tape Measure is used to measure the engine pulley diameters. Both drive and driven pulleys can be tested for vibration and noise by the iVA if the pulley diameters are known.

iVA Stereo Earphones
The iVA Stereo Earphones allow you to hear the noise from each individual microphone

USB Program Card
The iVA USB Program Card allows you to install the advanced iVA program onto your PC. If you need assistance with the iVA program or use of the iVA call ATS Support at 1-800-572-6112. ATS Support is free for 1 year and is USA based.
Need a Computer?
The Ruggedized Tablet Has You Covered!
System Requirements
Runs on most Intel or AMD Processor Windows based PC with type A USB 2.0 port.
Will NOT run on the Microsoft Surface Pro X ARM64-based PC with the Microsoft SQ1 processor.
Windows 7 Service Pack 1 through Windows 11 operating systems including Windows 11 tablets
(Windows RT tablets are not supported)